Stauff hydraulic filter element rp050e05

Xiamen Shengqi Electromechanical Equipment Co
, Ltd
Huang Gong: 18106908806 (wechat)
Fixed line: 0592-6081295
QQ:2761306899
Thank you for visiting Xiamen Shengqi website! Inquiry purchase Xiaohuang second reply
Smk20, K-type jic37 degree taper pipe joint
(in accordance with sae-j514)
JIC 37 degree taper pipe joint, in accordance with sae-j514
Type A, integrated
Type B, threaded in, split type
Metal parts
Steel, zinc nickel coating without hexavalent chromium = c6f
If you need to order stainless steel V2a (1
4305), please put the
Replace c6f with V2a
If you need to order stainless steel V4A (1
4571), please put the
Replace c6f with V4A
seal up
If you need to order FPM sealing products, please replace P in the order code with V
If you need to order EPDM sealing products, please replace P in the order code
Replace with E
The standard model is FPM fluororubber seal
Protective cap
Standard material: Steel
If you need to order steel hexagonal protective cap, please add - SK in the order code
(such as smk20-jic5 / 16-pk-sk-c6f)
If you need to order plastic protective caps, please add - KK in the order code
(such as smk20-jic5 / 16-pk-kk-c6f)
A
B (Hex
67)
Hex A
SW 17
Pipe diameter JIC overall dimension interface thread type
D size (mm / in) NBR seal FPM * seal
SMK20-JIC1/4-PK-C6F
SMK20-JIC1/4-VK-C6F
SMK20-JIC5/16-PK-C6F
SMK20-JIC5/16-VK-C6F
SMK20-JIC3/8-PK-C6F
SMK20-JIC3/8-VK-C6F
SMK20-JIC1/2-PK-C6F
SMK20-JIC1/2-VK-C6F
SMK20-JIC5/8-PK-C6F
SMK20-JIC5/8-VK-C6F
SMK20-JIC3/4-PK-GS 
SMK20-JIC3/4-VK-C6F
SMK20-JIC1-PK-GS  C6F
SMK20-JIC1-VK-GS-C6F
SMK20-JIC1-1/4-PK  GS-C6F
SMK20-JIC1-1/4-VK-GS-C6F
SMK20-JIC1-1/2-PK  GS-C6F
SMK20-JIC1-1/2-VK-GS-C6F
Installation of ferrule type pipe joint
Connector overview
Single ferrule
card
Part composition: joint body, ferrule and nut
When the ferrule and nut are sleeved on the steel pipe, insert the grounding
cone
Effective Migui
The commonly used single ferrule joint consists of a single edge
Edge ferrule
Single edge ferrule joints are as follows
Cutting edge ferrule
Sub insertion
protect
bottom
The right end of the ferrule is pressed by the tightening of the nut, and the left end is squeezed
In the gap between the conical hole in the inlet body and the pipe, the outer conical surface of the ferrule forms a conical contact seal, and the inner edge of the ferrule (1
Embedded steel pipe
A closed annular groove is pressed out of the outer wall of the steel pipe
Ring opening protrusion
The middle part of the nut is slightly deformed, and the snap sleeve is slightly deformed
Generate friction to prevent the nut from loosening
The elastic deformation part can absorb the vibration in the hydraulic pipeline
In addition, it is stuck
The steel pipe forms a conflict
The structure of edge ferrule joint is as follows
The edge ferrule joint uses two edge ferrules, i
e
one cutting edge
Stop edge (2)
It can cut into the cutting edge and bite the pipe, so as to improve the vibration resistance of the joint
Disconnection
meet
card
The ferrule type pipe joint is composed of four parts: joint body, front ferrule, rear ferrule and screw mu
When the ferrule and nut are on the steel pipe
After inserting the connector body, when tightening the screw mu, the ferrule stands in front
The conical surface of the joint body is fitted, and the inner edge is evenly bitten without damage
Tube to form an effective seal
Ferrule joint
1
Saw off the seamless steel pipe of appropriate length and remove the port burr
The steel pipe section shall be perpendicular to the axis and the angle shall be
Fruit steel pipe needs
Straight from steel pipe section to bending part
Length of
2
Put the nut and ferrule on the seamless steel pipe
Pay attention to nuts and ferrules
back
Apply lubricating oil on the thread and ferrule of the joint body, and insert the steel pipe
The steel pipe must be inserted
Understanding of ball valve and pneumatic actuator
The No
5 valve chamber of Maoda pipeline is located beside the river bank and the terrain is low
After the severe flood,
The actuator of valve chamber 5 began to leak
Based on this, I carefully study the basic of No
5 valve chamber
Equipment, learn relevant knowledge of ball valve and actuator through self-learning and from others,
Make the following summary

Introduction to ball valve Stauff hydraulic filter element rp050e05b
Ball valve - (ball vavle)
The closing part is a sphere, which rotates around the center line of the reading body to open and close
A kind of valve
Working principle Stauff hydraulic filter element rp050e05b
The ball valve has the action of rotating 90 degrees
The cock body is a sphere with circular through holes or through holes
The road passes through its axis
Ball valve is mainly used to cut off, distribute and change the flow of medium in the pipeline
In the moving direction, it can be closed only by rotating 90 degrees and a small rotating torque
Secret
Ball valve Zui is suitable for use as switch and shut-off valve,